1. Hey guyz. Welcome to the All New Phlatforum!



    Sign Up and take a look around. There are so many awesome new features.

    The Phlatforum is a place we can all hang out and

    have fun sharing our RC adventures!

  2. Dismiss Notice

Rafale !!!

Discussion in 'Single Wing Aircraft Plans' started by ewo, Mar 30, 2010.

  1. ewo

    ewo Moderator Staff Member

    Offline
    Messages:
    701
    Trophy Points:
    18
    Location:
    Indiana
    I think im gonna have to test this one myself first ! ;)

    Attached files [​IMG]
     
  2. theothers

    theothers Administrator Staff Member

    Offline
    Messages:
    761
    Trophy Points:
    18
    Location:
    New Jersey
    Looking good ewo. Let us know how she flies!

    Mark and Trish
     
  3. filthybeast

    filthybeast New Member

    Offline
    Messages:
    67
    Trophy Points:
    0
    Location:
    Upper Lake Ca
    I can't resist a delta wing canard, lookin forward to this one!
     
  4. kram242

    kram242 Administrator Staff Member

    Offline
    Messages:
    6,311
    Trophy Points:
    13
    Location:
    NJ
    ewo I am going to move this into the scratch built section until the code is ready for it. Hope that you don't not mind just trying to keep all the plans under the categories section complete plans. Usually we try to move any completed project from the scratch built section into there categories so that when people are searching for plans they can grab the file.
    Thanks in advance
    Mark
     
  5. ewo

    ewo Moderator Staff Member

    Offline
    Messages:
    701
    Trophy Points:
    18
    Location:
    Indiana
    No problems Mark ! ;)

    I really didnt know were to post this anyways. The files are ready for 3mm depron . I was going to wait to post the code untill i had it resized for the blu that most of you guys use ...

    I dont build planes anymore with that stuff so im not gonna go to the trouble of resizing and retabbing.

    I will post the code later today for the little depron model though. When mine finishes cutting.
     
  6. kram242

    kram242 Administrator Staff Member

    Offline
    Messages:
    6,311
    Trophy Points:
    13
    Location:
    NJ
    :D thanks ewo :D Looking forward to it. I have some 3mm in house so I am good to go! :mrgreen:
     
  7. 7up

    7up Moderator Staff Member

    Offline
    Messages:
    1,090
    Trophy Points:
    38
    Location:
    Kentucky
    Looks pretty cool ewo!
     
  8. ewo

    ewo Moderator Staff Member

    Offline
    Messages:
    701
    Trophy Points:
    18
    Location:
    Indiana
    Im pretty well happy with the way it turned out but i did have some trouble with my machine

    My x axis is acting up really bad..... it dont run unless i have the x vrev turned all the way up.?
    does that mean i need new stepper motors?? :shock:

    any ways here are the files for this 21" little gem ! All the parts fit nice and snug , I really like that.
    I sized the slots at 3/32" and the tabs fit nice and snug. :D
    I did however make only a few changes just to suit myself ! :)

    Anyways Enjoy ! ;)
    OH --- The original files can be found Here along with several other really nice plane dxf files :mrgreen:
    http://www.aeroplaza.nl/ Attached files Rafale.skp (623.7 KB)Â rafiell-21.cnc (22.3 KB)Â [​IMG] [​IMG]
     
  9. crash5050

    crash5050 Member

    Offline
    Messages:
    190
    Trophy Points:
    16
    Location:
    Greenwood/ Fort Smith, Arkansas
    Awesome Job, Bruce. I can't wait until UPS brings my Depron.
     
  10. kram242

    kram242 Administrator Staff Member

    Offline
    Messages:
    6,311
    Trophy Points:
    13
    Location:
    NJ
    That looks SWEET!! Nice job :)
    Thank you for sharing this

    Try turning the power off to the board and wiggle/ push the big driver chips in lightly
    Then turn it back on and see if that helps. Over time the vibration of the machine can work them loose a little causing them to act up.
    Hope this helps
    Mark
     
  11. ewo

    ewo Moderator Staff Member

    Offline
    Messages:
    701
    Trophy Points:
    18
    Location:
    Indiana
    whoa there ! If you downloaded the files ditch them. I forgot some tabbing in some key places on the files i had here ! :?

    Please download the updated files.

    I recut the plane because i like it so much, i wanted 2 of them Thats when i discovered the oversite.

    Please forgive my oversite
     
  12. kram242

    kram242 Administrator Staff Member

    Offline
    Messages:
    6,311
    Trophy Points:
    13
    Location:
    NJ
    Got'em thanks for the updated ewo
    Mark
    p.s.moving this over into single wing category :D
     

Share This Page