1. Hey guyz. Welcome to the All New Phlatforum!



    Sign Up and take a look around. There are so many awesome new features.

    The Phlatforum is a place we can all hang out and

    have fun sharing our RC adventures!

  2. Dismiss Notice
Welcome to The Phlatforum PhlatPrinter III

My hard drive crashed!

Discussion in 'SketchUcam Help' started by AnyAirRc, Dec 11, 2009.

  1. AnyAirRc

    AnyAirRc Moderator

    Offline
    Messages:
    227
    Trophy Points:
    0
    Hey guys my CNC pc just took a poo.... I need to download Mach3 again and my question is what version works with the older phlatscript files? I remember I needed a certain version when the phlatprinter mkI came out...
     
    AnyAirRc, Dec 11, 2009
    #1
  2. kram242

    kram242 Administrator Staff Member

    Offline
    Messages:
    6,311
    Trophy Points:
    13
    Location:
    NJ
    AnyairRC that stinks for sure!
    Hope you had a back up going?
    The version I am using is R2.60 Its stable and works fro what I need.
    As for needing a certain version, they all should work fine
    You can go to www.machsupport.com and download the latest stable release
    or you could use the R2.60 version
    You can download that version here
    viewtopic.php?f=130&t=18&start=0
    Good luck with reboot
    I know it does seem lame but on the bright side you will have a new clean slate to work with :)
    I sometimes wish my computer would crash just so I would be forced to start over and have a nice fast clean system again, but alas I have a Dell :D
    Mark
     
    kram242, Dec 11, 2009
    #2
  3. frankrcfc

    frankrcfc New Member

    Offline
    Messages:
    381
    Trophy Points:
    0
    Location:
    Battle Creek, Mi
    Hey anyair. been there done that earlier this summer. Is'nt any fun trying to get those special settings back. I went and got a 1 terra byte external harddrive with automatic updating and have had good peace of mind since then. Like Mark say's that version 2.60 works great and is very stable. Just drop your license file given you in the mach folder and your up and running again. ;)
     
    frankrcfc, Dec 11, 2009
    #3
  4. AnyAirRc

    AnyAirRc Moderator

    Offline
    Messages:
    227
    Trophy Points:
    0
    Ok got it guys thanks, how about that mach3 setup video??? I have been searching for a bit now...

    I wish my MacBookPro would run Mach3 and the phlatscript, then I wouldn't have three different computers with data scattered around....
     
    AnyAirRc, Dec 11, 2009
    #4
  5. kram242

    kram242 Administrator Staff Member

    Offline
    Messages:
    6,311
    Trophy Points:
    13
    Location:
    NJ
    Anyair,
    I believe from when you bought your machine we have since started to include DVD setup disk instead of the motion box video downloads.
    We will have to send you a set for the MKI
    Please PM me the address you want me to send them to.
    In the mean time this thread may help you to get back up and running
    The setting here are for the MKII so you will have to adjust your motor tunings accordingly but other than that you should be fine.
    viewtopic.php?f=130&t=1376&start=0
     
    kram242, Dec 11, 2009
    #5
  6. AnyAirRc

    AnyAirRc Moderator

    Offline
    Messages:
    227
    Trophy Points:
    0
    Got my disk thanks! I'll have to fix up my PP comp after Christmas. Have a good one everyone!
     
    AnyAirRc, Dec 22, 2009
    #6
  7. kram242

    kram242 Administrator Staff Member

    Offline
    Messages:
    6,311
    Trophy Points:
    13
    Location:
    NJ
    Good to hear! :) You and your family have a great Christmas too!
    Mark
     
    kram242, Dec 22, 2009
    #7

Share This Page