1. Hey guyz. Welcome to the All New Phlatforum!



    Sign Up and take a look around. There are so many awesome new features.

    The Phlatforum is a place we can all hang out and

    have fun sharing our RC adventures!

  2. Dismiss Notice
Welcome to The Phlatforum PhlatPrinter III

Setting up mach 3 for the Mark1

Discussion in 'Trouble Shooting - Support - Help Section' started by filthybeast, Jan 20, 2010.

  1. filthybeast

    filthybeast New Member

    Offline
    Messages:
    67
    Trophy Points:
    0
    Location:
    Upper Lake Ca
    Cant seem to get it to work, I followed mach3 quickstart guide & went thru crash's build log for the mark1 but still no go, is there a more detailed setup guide someone can link me. My machine works just fine with emc2 so I know there is nothing wrong with it, I must be doing something wrong in the mach3 configs.
     
    filthybeast, Jan 20, 2010
    #1
  2. 3DMON

    3DMON Moderator Staff Member

    Offline
    Messages:
    2,380
    Trophy Points:
    38
    Location:
    Sebastian, Florida
    Didn't the vids that you got with the MK1 have Mark showing how to set up Mach?
    They helped me tremendously in the beginning.
     
    3DMON, Jan 20, 2010
    #2
  3. filthybeast

    filthybeast New Member

    Offline
    Messages:
    67
    Trophy Points:
    0
    Location:
    Upper Lake Ca
    Never got a dvd, i used the vids from the phlatboyz site and they seem to be gone now- There was link there to the vids, been so long just dont remember, still have my password tho-
     
    filthybeast, Jan 20, 2010
    #3
  4. 3DMON

    3DMON Moderator Staff Member

    Offline
    Messages:
    2,380
    Trophy Points:
    38
    Location:
    Sebastian, Florida
    Oh. I think I saw where Mark would send you a dvd in a previous post somewhere. Those vids are the best way to go for setting it up.
     
    3DMON, Jan 20, 2010
    #4
  5. filthybeast

    filthybeast New Member

    Offline
    Messages:
    67
    Trophy Points:
    0
    Location:
    Upper Lake Ca
    Thanks, Ill send a pm to him and see if I can get one-

    Fred
     
    filthybeast, Jan 20, 2010
    #5
  6. kram242

    kram242 Administrator Staff Member

    Offline
    Messages:
    6,311
    Trophy Points:
    13
    Location:
    NJ
    Fred,
    Just now saw this post
    Sorry we had to take down the old ones as Motion box kept raising their prices on us, so we opted to go the DVD route.
    We will get them in the mail to you ASAP :)
    Thank you
    Mark and Trish
     
    kram242, Jan 20, 2010
    #6
  7. filthybeast

    filthybeast New Member

    Offline
    Messages:
    67
    Trophy Points:
    0
    Location:
    Upper Lake Ca
    Well I just wouldnt give up, stayed up till 3:30 this mornin and finally got it up and working. Fnally figured out the prob was with windows, never did figure exactly what but after a clean install of windows & mach3 did it. Nice job on the mach3 phlatscreen by the way, I really like it! Prob not the last time Im going to have to reinstall so that dvd would still be nice to have.
    I used the oldladys CC when I bought my phlatty, so my addy should be under Venus Wilson-

    Thanks Mark!
     
    filthybeast, Jan 21, 2010
    #7
  8. kram242

    kram242 Administrator Staff Member

    Offline
    Messages:
    6,311
    Trophy Points:
    13
    Location:
    NJ
    Ok I have them on disk and will send them out under that address.
    Mark
     
    kram242, Jan 21, 2010
    #8

Share This Page