1. Hey guyz. Welcome to the All New Phlatforum!



    Sign Up and take a look around. There are so many awesome new features.

    The Phlatforum is a place we can all hang out and

    have fun sharing our RC adventures!

  2. Dismiss Notice
Welcome to The Phlatforum PhlatPrinter III

Recent Content by rcflyboynj

  1. rcflyboynj
    Post

    Pilot Life

    Thanks!!
    Post by: rcflyboynj, Jun 20, 2014 in forum: General Talk Forum
  2. rcflyboynj
    Post

    Pilot Life

    Just thought I'd drop by for a quick update, I graduated from Louisburg High School and then a week later passed my checkride for my pilots...
    Post by: rcflyboynj, Jun 8, 2014 in forum: General Talk Forum
  3. rcflyboynj
    Thread

    Pilot Life

    I know I haven't been as busy as I like creating epic creations on the PhlatPrinter, but I have been busy with one other thing. I have been...
    Thread by: rcflyboynj, Aug 1, 2013, 5 replies, in forum: General Talk Forum
  4. rcflyboynj
    Post

    OpenRail camera slider?

    Let me know how it turns out! I was thinking the exact same thing the other day!!! ~ Nathan
    Post by: rcflyboynj, Aug 1, 2013 in forum: OpenBuilds Projects
  5. rcflyboynj
    Post

    rcflyboynj's Build

    Cut out a "Powercat...." The mascot of Kansas State University and Louisburg High School...... :good2: Worked great. :banger: Shot a video,...
    Post by: rcflyboynj, Jan 6, 2013 in forum: Phlatprinter BUILD LOGS
  6. rcflyboynj
    Post

    rcflyboynj's Build

    :dance3: :biggrin: :-D :good: :doubleup: :banger: :flying: :dance: :good2: :fantastic: :Connie_happy-mail: :drinks: :worship:...
    Post by: rcflyboynj, Dec 30, 2012 in forum: Phlatprinter BUILD LOGS
  7. rcflyboynj
    Post

    rcflyboynj's Build

    Ok. I think I figured it out. Just need to make sure everything is calibrated before the first cut!! Thanks TigerPilot!! :doubleup: Also, is...
    Post by: rcflyboynj, Dec 14, 2012 in forum: Phlatprinter BUILD LOGS
  8. rcflyboynj
    Post

    rcflyboynj's Build

    Still haven't figured it out yet. Should I be running slower kernel speed? Thanks, Nathan
    Post by: rcflyboynj, Dec 8, 2012 in forum: Phlatprinter BUILD LOGS
  9. rcflyboynj
    Post

    rcflyboynj's Build

    Thanks Paule. You're getting close when you hit the electronics! Not much further to go! :good: ~Nathan
    Post by: rcflyboynj, Nov 29, 2012 in forum: Phlatprinter BUILD LOGS
  10. rcflyboynj
    Post

    rcflyboynj's Build

    Mark, Thank you for the suggestions. The wire blocks were fine, it was the screws on the actual driver board. Talked to a friend in home...
    Post by: rcflyboynj, Nov 29, 2012 in forum: Phlatprinter BUILD LOGS
  11. rcflyboynj
    Post

    rcflyboynj's Build

    No cuts yet. Still trying to figure out how to get the wires connected securely to the driver. The supplied screw connectors with the board are...
    Post by: rcflyboynj, Nov 24, 2012 in forum: Phlatprinter BUILD LOGS
  12. rcflyboynj
    Post

    rcflyboynj's Build

    Thanks Mark for the 16th step and 3500 hz input. It's working great! :doubleup: Until the wires come lose from the circuit board. :dash1: Need...
    Post by: rcflyboynj, Nov 21, 2012 in forum: Phlatprinter BUILD LOGS
  13. rcflyboynj
    Post

    rcflyboynj's Build

    Here's the manual for the board I'm using... not entirely sure how I should set the dip switches. Also, I'm getting a grinding noise from the...
    Post by: rcflyboynj, Nov 19, 2012 in forum: Phlatprinter BUILD LOGS
  14. rcflyboynj
    Post

    rcflyboynj's Build

    Hey guys... guess what.... I'M DONE!!!!!! Software this weekend....
    Post by: rcflyboynj, Nov 15, 2012 in forum: Phlatprinter BUILD LOGS