1. Hey guyz. Welcome to the All New Phlatforum!



    Sign Up and take a look around. There are so many awesome new features.

    The Phlatforum is a place we can all hang out and

    have fun sharing our RC adventures!

  2. Dismiss Notice
Welcome to The Phlatforum PhlatPrinter III

Full Fuse Lil' Ripper

Discussion in 'Single Wing Aircraft Plans' started by 3DMON, Oct 29, 2009.

Page 3 of 4
  1. 3DMON

    3DMON Moderator Staff Member

    Offline
    Messages:
    2,380
    Trophy Points:
    38
    Location:
    Sebastian, Florida
    lol...see if you checked out my site you might have seen the instructions.
    There are a few more changes to the new version than just the tube slot but the version you have flies pretty much the same.
     
    3DMON, Jun 28, 2010
    #51
  2. frankrcfc

    frankrcfc New Member

    Offline
    Messages:
    381
    Trophy Points:
    0
    Location:
    Battle Creek, Mi
    DRAT! busted :oops: . Actually After I took those shots I THEN looked at your build pictures and spotted that mistake. I was able to cut that out and correct it though.
     
    frankrcfc, Jun 28, 2010
    #52
  3. 3DMON

    3DMON Moderator Staff Member

    Offline
    Messages:
    2,380
    Trophy Points:
    38
    Location:
    Sebastian, Florida
    Be sure to look over the instructions. They are way better than the old builds pics I had up before.
    Glad you caught it before the whole plan was built though. It would get tricky getting the electronics in there :lol:
     
    3DMON, Jun 28, 2010
    #53
  4. cncmachineguy

    cncmachineguy Member

    Offline
    Messages:
    133
    Trophy Points:
    16
    Location:
    Odenton MD
    Well I actually have looked at your site, but somehow missed it. :oops:
     
    cncmachineguy, Jun 28, 2010
    #54
  5. 3DMON

    3DMON Moderator Staff Member

    Offline
    Messages:
    2,380
    Trophy Points:
    38
    Location:
    Sebastian, Florida
    Lol, I was just pulling your leg Bert. I meant to put the link to the instructions here earlier but forgot.
     
    3DMON, Jun 28, 2010
    #55
  6. frankrcfc

    frankrcfc New Member

    Offline
    Messages:
    381
    Trophy Points:
    0
    Location:
    Battle Creek, Mi
    Heck with that. I'd turn it into an "instant free flying glider :D
     
    frankrcfc, Jun 28, 2010
    #56
  7. cncmachineguy

    cncmachineguy Member

    Offline
    Messages:
    133
    Trophy Points:
    16
    Location:
    Odenton MD
    good thing cuz thats how I took it. But I really have surfed your site. :D BTW did you get the F22 kit up yet?
     
    cncmachineguy, Jun 28, 2010
    #57
  8. 3DMON

    3DMON Moderator Staff Member

    Offline
    Messages:
    2,380
    Trophy Points:
    38
    Location:
    Sebastian, Florida
    f22 kit has been up the whole time LOL.
     
    3DMON, Jun 28, 2010
    #58
  9. cncmachineguy

    cncmachineguy Member

    Offline
    Messages:
    133
    Trophy Points:
    16
    Location:
    Odenton MD
    :oops:
     
    cncmachineguy, Jun 28, 2010
    #59
  10. rayclark

    rayclark Member

    Offline
    Messages:
    134
    Trophy Points:
    18
    Location:
    Center of Michigan
    Shaun,

    Are the files posted in the 1st post the latest version ?? Just wondering cause I am getting ready to build this one and wanted to be sure to get the newest version.

    Thanks
    Ray C
     
    rayclark, Jun 28, 2010
    #60
  11. frankrcfc

    frankrcfc New Member

    Offline
    Messages:
    381
    Trophy Points:
    0
    Location:
    Battle Creek, Mi
    Oh before I forget Shaun. How far apart are those step cuts for the hinge area? Looks like 1/16 ?
     
    frankrcfc, Jun 28, 2010
    #61
  12. 3DMON

    3DMON Moderator Staff Member

    Offline
    Messages:
    2,380
    Trophy Points:
    38
    Location:
    Sebastian, Florida
    Hi Ray, no those codes are the older ones. Give me a day or 2 and I will post the new ones.

    Frank the new files I will be posting soon have the hinge lines better. I think that file the lines are 1/16" apart. Oh but now I that think of it my cuts will show different anyways. See I use an odd size bit (.078) but when I re post the files I will change it accordingly.
     
    3DMON, Jun 28, 2010
    #62
  13. 3DMON

    3DMON Moderator Staff Member

    Offline
    Messages:
    2,380
    Trophy Points:
    38
    Location:
    Sebastian, Florida
    Ok guys!

    I got the newest Lil' Ripper files posted on the first post.

    The files are worked up for an 1/8" bit.
     
    3DMON, Jun 30, 2010
    #63
  14. frankrcfc

    frankrcfc New Member

    Offline
    Messages:
    381
    Trophy Points:
    0
    Location:
    Battle Creek, Mi
    Sweet! Thank you. I am grabbing those. Heck one sheet to make this little gem I can't lose with this latest file :D ;)
     
    frankrcfc, Jun 30, 2010
    #64
  15. AnyAirRc

    AnyAirRc Moderator

    Offline
    Messages:
    227
    Trophy Points:
    0
    Man I think this is just what I needed. I was going to design a 3d plane like my PA Addiction but the ripper is killer and fits what power system I have. I plan on cutting out one of these very soon!
     
    AnyAirRc, Jun 30, 2010
    #65
  16. 3DMON

    3DMON Moderator Staff Member

    Offline
    Messages:
    2,380
    Trophy Points:
    38
    Location:
    Sebastian, Florida
    Your welcome Frank!

    Cool AnyAir! What power setup you planning to use?
     
    3DMON, Jun 30, 2010
    #66
  17. AnyAirRc

    AnyAirRc Moderator

    Offline
    Messages:
    227
    Trophy Points:
    0
    I have the 1300kv blue wonder and 3s 620mah packs... I was blown away at the hovers, KE spins and snaps it is hard to make a foamy do it all well and you did it, great job!
     
    AnyAirRc, Jul 1, 2010
    #67
  18. 3DMON

    3DMON Moderator Staff Member

    Offline
    Messages:
    2,380
    Trophy Points:
    38
    Location:
    Sebastian, Florida
    Awesome. That is exactly the setup I'm running and found The Lil' Ripper to fly the best with it.
    On the knife edge spins, I found it goes into them best at a little less than half throttle.
     
    3DMON, Jul 1, 2010
    #68
  19. almostthere

    almostthere New Member

    Offline
    Messages:
    52
    Trophy Points:
    0
    Location:
    Anna tx.
    awsome plane 3dmon it flys great but mine come out real tail heavy i got a bw 1700 and a 450 hyperion battery I have to use 2 battery to get the cg where it needs to be. But it still flys awsome.

    Attached files [​IMG] [​IMG] [​IMG] [​IMG]
     
    almostthere, Oct 20, 2010
    #69
  20. 3DMON

    3DMON Moderator Staff Member

    Offline
    Messages:
    2,380
    Trophy Points:
    38
    Location:
    Sebastian, Florida
    Hey almostthere,

    Your Lil' Ripper looks great!
    With the 1700kv on there I'm guessing you went with a 2 cell pack.
    I think your having balance issues because of the size of battery. I use a 3s 600 lipo.

    Glad you like the plane.
     
    3DMON, Oct 20, 2010
    #70
  21. crash5050

    crash5050 Member

    Offline
    Messages:
    190
    Trophy Points:
    16
    Location:
    Greenwood/ Fort Smith, Arkansas
    What happened to the wood parts files? I know they were there at one time...
     
    crash5050, Dec 19, 2010
    #71
  22. 3DMON

    3DMON Moderator Staff Member

    Offline
    Messages:
    2,380
    Trophy Points:
    38
    Location:
    Sebastian, Florida
    Hmmm. I don't know. I thought I put them there. I'll try to add them by tomorrow morning.

    They are for 1/16th bit.
     
    3DMON, Dec 19, 2010
    #72
  23. 3DMON

    3DMON Moderator Staff Member

    Offline
    Messages:
    2,380
    Trophy Points:
    38
    Location:
    Sebastian, Florida
    First post has been updated with the wood parts and I added the overhead gantry gcode files.

    Thanks for bringing this to my attention crash5050.
     
    3DMON, Dec 20, 2010
    #73
  24. jovian

    jovian Member

    Offline
    Messages:
    208
    Trophy Points:
    16
    I am going to have to make one of these once I get my mk 3 fully running. It looks sweet.
     
    jovian, Dec 21, 2010
    #74
  25. 3DMON

    3DMON Moderator Staff Member

    Offline
    Messages:
    2,380
    Trophy Points:
    38
    Location:
    Sebastian, Florida
    Thanks jovian.
    Please post if you do. I like hearing how people feel about my designs.
     
    3DMON, Dec 21, 2010
    #75
Page 3 of 4

Share This Page